Electro-Numerics, Inc.
42213 Sarah Way, Temecula, CA 92590, USA


Tel: 800-854-8530 (USA)
Tel: 951-699-2437 
Fax: 951-695-7246


    Micro Series Dual-Channel
Up/Down Totalizer & Rate Meter

With two independently scalable channels & presets

Standard Counter

  • Available in three digit heights: 0.56" for panel mounting, 1.0" (Mighty-1), and 5.0" (Mighty-5) for long-distance viewing.
  • Independent, scalable totals for Channels A & B.
  • Totals stored in non-volatile memory.
  • Inputs from NPN or PNP proximity switches, contact closures, digital logic, 
    magnetic pickups down to 12 mV, or AC inputs up to 250 Vac.
  • Up counting from zero to preset value using positive scale factor.
  • Down counting from preset to zero using negative scale factor.
  • Data rates up to 1 MHz.
  • Isolated 5, 10 or 24 Vdc excitation supply to power sensors.
  • Green or red LED display.
  • Choice of isolated plug-in options for control and computer interface:
    dual relays, 4-20 mA & 0-10 V analog output, RS232/485 serial I/O, low voltage AC & DC power.
  • 1/8 DIN version environmentally sealed to NEMA-4X from front panel.
  • 1/8 DIN version certified to UL 3101-1, CAN/CSA-C22.2, EN 61010-1 (CE Mark).

Extended Counter

All capabilities of the Standard Counter, plus:
  • Channel A total and Channel B rate simultaneously.
  • Up/down counting on Channel A, using Channel B to control count direction.
  • Counting on Channel A, using Channel B to inhibit counting.
  • Arithmetic functions A+B, A-B, A*B, A/B


Signal conditioner for Laureate Dual-Channel Up/Down TotalizerThe Micro dual-channel up or down totalizer is a basic operating mode of the Micro counter with the FR dual-channel signal conditioner board.

Each channel (A or B) may be independently set up and scaled to count up from zero (or other value) to a preset limit, or to count down from a preset value to zero (or other limit). Countdown operation is set up by entering a negative scale factor.

The six-digit counter display is capable of displaying any value from -999,999 to 999,999 with programmable decimal point. Scaling allows direct readout in engineering units, such as gallons or cubic feet based on counts from a turbine flowmeter, or the count of cans based on the count of six-packs. The displayed channel (A or B) is selected via a front panel pushbutton. The totals are stored in non-volatile memory so as to be retained in the absence of power.

The minimum recommended complementary option for the Micro totalizer is the dual setpoint controller output board, which is available with either 8A relays or AC/DC solid state relays.

Extended Counter Capabilities

An optional Extended counter version provides capabilities beyond those of the standard counter:

  • Rate and total simultaneously. Channel A can display total while Channel B displays rate. The selection of A or B for display is via a front panel pushbutton. This mode is ideal for flow applications.

  • Up/down counting. Channel A can serve as an up/down counter, where the count direction is dynamically changed by applying a signal to Channel B. For instance, Channel A can count and scale pulses from a turbine flowmeter, while Channel B inputs the direction of flow. This allows total volume to be tracked in case of reversible flow.

  • Totalizing with external inhibit. Totalizing by Channel A can be temporarily inhibited by applying a signal to Channel B. For instance, 60 Hz AC pulses can be counted by Channel A and be scaled to display elapsed hours. A signal can be applied to Channel B to start or stop pulse counting when a process is in operation.

  • Custom curve linearization. Exceptionally accurate custom curve linearization is achievable, for example to linearize the low end of turbine flowmeters. For setup, up to 240 data points can be input into a spreadsheet or text file by the user. The computer then calculates spline fit segments, which are downloaded into the meter via RS232. The linearized rate can then be totalized by the Extended counter.

  • Arithmetic functions. The Extended counter makes arithmetic functions available, namely A+B, A-B, A*B, A/B and A/B-1. These solve many applications. For instance, A+B allows two input flows to be summed for total volume, while A-B allows outflow to be subtracted from inflow for net volume. A/B allows the mixing of ingredients in a specified ratio. By monitoring and alarming the A/B volume ratio, ingredient B can be added to A until the proper ratio is achieved.

Universal Signal Conditioner

The dual-channel signal conditioner accepts inputs from proximity switches with PNP or NPN output, TTL or CMOS logic, magnetic pickups, contact closures, low-level outputs from turbine flow meters down to 12 mV, and high-level AC line inputs up to 250 Vac. Jumper selections provide optimum operation for different sensor types and noise conditions.

A built-in isolated 5, 10, or 24 Vdc excitation supply can power proximity switches and other sensors, and eliminate the need for an external power supply.

Built-in Flexibility

Plug-in isolated analog output, dual relay controller, and RS232/485 serial communication boards can upgrade Micro and Mighty Series totalizer from a stand-alone monitor to system interface and control. The ability of the Micro Series totalizer to output an isolated 4-20 mA signal which tracks a total may be unique among totalizers.

Micro Series meters can be powered from 95-240 Vac 10% and 95-370 Vdc, or optionally from 12-34 Vac and 10-48 Vdc. Any setup functions and front panel keys may be locked out for simplified usage and security. The popular 1/8 DIN version with 0.56" high digits is environmentally sealed to NEMA-4X (IP65) from the front when panel mounted, and is available with red or green LEDs.


Digit Height
6 digits, 7-segment
Available with 0.56", 1.0", 4.0" or 5.0" digits.

High brightness red. Green available with 0.56" digits.
-999999 to +999999, XXXXEX scientific notation beyond 999999
Four LED lamps
Signal ground
Channel A Frequency
Channel B Frequency
Selectable Hysteresis
Rolloff Filter
Debounce Time

AC, pulses from NPN, PNP transistors, contact closures, magnetic pickups
Common ground for channels A & B
0 Hz to 1 MHz
0 Hz to 250 kHz
-12 mV to +12 mV, +30 mV to +60 mV, -30 mV to -20 mV,
-150 mV to +150 mV, +350 mV to +600 mV, -600 mV to -350 mV,
-1.15 V to +1.15 V, +1.25 V to +2.1 V, -2.1 V to -1.25 V
Selectable: 1 MHz, 30 kHz,  250 Hz
Selectable: 0, 3, 50 ms

Voltage, std.
Voltage, opt.
Power isolation
95-240 Vac 10% and 95-370 Vdc
12-34 Vac and 10-48 Vdc
DC or 49-440 Hz
Safety-rated to 250 Vac, meter ground to earth ground,
DC to 60 Hz, 4.2 kVp per High Voltage Test
Excitation Output
5 Vdc
10 Vdc
24 Vdc
Output isolation
5 Vdc 5%, 100 mA max
10 Vdc 5%, 120 mA max
24 Vdc 5%, 50 mA max
50 Vdc to meter ground
Operating Temperature
Storage Temp.
Relative Humidity
0C to 60C
-40C to 85C
95% at 40C, non-condensing
NEMA-4X (IP-65) when panel mounted
Electrical Connections
condualnobox.gif (1188 bytes)

Typical Applications

Up/Down Totalizing

Dual-channel up/down totalizing using one channel for counts and one channel for count direction

Up/down totalizing is provided by a mode of the Extended counter where pulses are either added or subtracted on Channel A based on a direction input on Channel B. The counter can also be programmed so that counting by Channel A is inhibited by an input on Channel B.

Combining Two Totals

Dual-channel up/down totalizing, where two channels are added or subtracted.

A+B, A-B and A/B arithmetic functions are available with the Extended counter. A+B sums both totals, while A-B subtracts the outflow total from inflow total. The A/B ratio applied to total helps assure the proper mixing of components.

Up or Down Counting with Preset

Two repetitive fill operations handled by a single Laureate dual-channel digital counter and totalizer

A single Micro dual-channel counter will handle two repetitive fill operations by counting from zero up to a preset, or down from a preset to zero. A dual setpoint relay board is required.

Machine ON Time and Utilization

Dual-channel up/down totalizing to measure machine ON time by counting power line cycles.

An easy way to measure the ON time of machines is to count AC line cycles and scale the total to hours. To display machine utilization or duty cycle in percent, use the Extended counter. Connect Channel A to switched AC and Channel B to the AC line, and have the counter display the A/B ratio with a 100 multiplier.

Total and Rate Simultaneously

Displaying rate and total in the same Laureate digital panel totalizer and rate meter.

The Extended version of the Micro dual channel counter can display scaled rate or total for the same channel at the push of a button, and alarm both the rate and total. The Extended version can also do curve linearization, thereby extending the working range and accuracy of flow transducers.

System-level Capabilities

System-level capabilities of Laureate dual-channel totalizer.

The Micro Series dual-channel totalizer can independently scale, display and alarm two totals, and the totals plus alarm data can be transmitted via RS232 or RS485. The displayed totals can also be transmitted as a scaled 4-20 mA analog output. The Extended version can further display and transmit arithmetic combinations of the two totals.

Micro & Mighty Series Downloads

Electro-Numerics Inc. Logo

Digital Panel Meters
by Series

 Micro Meter/Controllers
 DIN Digital Indicators
 Summit Low Cost Meters
 Older Digital Panel Meters
 Catalogs & Price Lists
 Meter Owners Manuals
 Micro Downloads
 Meters Inquiry & RFQ


Large Digit Industrial Displays

 Mighty Series (to 5" LED)
 PI Series (2" LED)
 Flip-Digit Series (to 9")

 Catalogs & Price Lists
 Large Digit Inquiry & RFQ


Custom Magnetic Components

 Custom Transformers
 Coils, Inductors, Toroids
 Magnetic Sensors
 Magnetics Inquiry & RFQ

Sports Timing
Race Clocks
(to 9")

 LM Series, Flip-Digit
 XL Series, LED, Domestic
 XLC Series, LED, Int'l
 Mile-Marker 6" Raceclock

 Printing Race Timers
 Serial Remote Displays
 Raceclock Accessories
 Raceclock Dimensions
 Catalogs & Price Lists
 Sports Timer Inquiry


Information about Electro-Numerics

 Electro-Numerics Home
 About Electro-Numerics
 Electro-Numerics News
 General Inquiry




Electro-Numerics, Inc., 42213 Sarah Way, Temecula, CA 92590, USA
Tel: 800-854-8530 (USA), 951-699-2437;  Fax: 951-695-7246;  sales@electronumerics.com