42213 Sarah Way, Temecula, CA 92590,
Tel: 800-854-8530 (USA)
Applicable to Digital Panel Meters,
& Remote Displays
95-240 Vac ±10% & 95-370 Vdc or 12-34 Vac &
10-48 Vdc Input
with 5, 10 & 24 Vdc Excitation Output
Shown above: power
input boards for 1/8 DIN Micro Series
Left: for 12-34 Vac & 10-48 Vdc. Right: for 95-240 Vac ±10% & 95-370 Vdc.
- Lightweight, high-frequency switching
power supply design.
- 95-240 Vac ±10% or 95-370 Vdc input
(standard) for worldwide AC operation without hardware modification.
- Includes 250 Vac resettable fuse.
- 12-34 Vac or 10-48 Vdc power
(optional with 0.56", 1.0" & 4.0" versions) allows
operation from batteries, 28 Vac, or 400 Hz aircraft power.
- Three selectable isolated excitation
5 Vdc at 100 mA, 10 Vdc at 120 mA, or 24 Vdc at 50 mA.
- Certified to UL 3101-1, CAN/CSA-C22.2,
and EN 61010-1 safety standards.
- Certification issued by CSA, a
Nationally Recognized Test Laboratory
(File No. 212851).
Micro digital panel meters, digital counters and 6-digit remote display offer a choice of
two high-frequency switching power supplies. These provide stable, isolated power for
instrument operation plus excitation outputs at a substantially reduced weight and over a
broader range of input voltages and power frequencies than conventional linear supplies.
High voltage AC or DC power.
The standard Micro supply accepts power from 85 to 264 Vac, 47 to 440 Hz. This allows
the same meter to operate worldwide without modification. The supply also accepts 90 to
Low voltage AC or DC power.
An optional low voltage supply operates from 9 to 37 Vdc or 8 to 28 Vac, 47 to 440
Hz. This supply allows the Micro to be powered from batteries or from 28 Vac, 400 Hz
Isolated Excitation Output
Each power supply provides
three jumper-selectable, isolated excitation outputs: 5 Vdc at 100 mA, 10 Vdc at 120 mA,
or 24 Vdc at 50 mA. These outputs can be used to power external sensors, transmitters and
up to four 350 ohm load cells, thereby avoiding the need for an expensive external supply.
When powering a load cell or potentiometer, a
ratiometric operating mode can be selected, where the meter monitors the excitation supply
and removes the effects of voltage variation.
In addition to the isolated excitation output,
regulated 5 Vdc at up to 50 mA is brought out and can be used to power external logic.
Wiring of Excitation Output
|4-wire, 4-20 mA
2-wire 4-20 mA
Both power supplies and their
connectors (standard) are designed to UL/IEC/CSA safety standards. The two Micro power supplies also do double-duty by providing two
connector inputs (A & B) and a digital ground for signals such as meter hold, reset,
tare, etc. These signals do not affect power supply operation.
95-240 Vac ±10% or
12-34 Vac or 10-48 Vdc
DC and 49-440 Hz
5.3 W max
Isolation to power ground
Isolation to meter ground
±5%, 100 mA max
10 Vdc ±5%, 120 mA max
24 Vdc ±5%, 50 mA max
50 mVp-p max
Safety-rated to 250 Vac, 4.2 kVp per High Voltage Test
Micro & Mighty Series Downloads