Electro-Numerics, Inc.
42213 Sarah Way, Temecula, CA 92590, USA

Raceclock

Tel: 800-854-8530 (USA)
Tel: 951-699-2437 
Fax: 951-695-7246

sales@electronumerics.com

    Micro Series Analog Output Option
Isolated 0-10 V & 0-20 mA analog output scaled to display
for digital panel meters, counters and remote displays

Features
  

  • 0-20 mA or 4-20 mA plus 0-10 Vdc
  • 0.025% resolution
  • Isolation to 250 Vac
  • Outputs linearized to reading
  • Scale and offset via RS232, RS485, or front panel
  • 56/s update rate at 60 Hz power, 47/s at 50 Hz power
  • 12 V compliance at 20 mA
  • Output derived from filtered or unfiltered signal input
Analog output option board for Micro™ digital panel meters and counters

Description

The Micro analog output option board provides an isolated 0-10 Vdc voltage signal to drive a chart recorder, plus an isolated 0-20 mA or 4-20 mA current signal for transmission to a computer or central control room. This option is compatible with all Micro meters and counters, and turns these into highly accurate, sourcing, 4-wire transmitters. The output for thermocouples, RTDs and custom curves is linearized to the displayed reading.

A 12-bit D-to-A converter provides .025% resolution. The update rate is a fast 56/s at 60 Hz power or 47/s at 50 Hz power. The analog output can track the unfiltered signal for fastest response, or the digitally filtered signal for best noise rejection.

Scaling of the output is easily entered via front panel pushbuttons or via the serial digital interface. The displayed readings to produce the low and high analog outputs may be set to any value from -99,999 to +99,999 for DPMs, or -999,999 to +999,999 for counters.

Both the current (0-20 mA or 4-20 mA) or voltage ( 0-10 V) outputs are available at the same time, and the same scaling applies to both. The output selected in software is calibrated to 99.9% accuracy. The non-selected output is accurate to 98%.

Isolation is provided by a separate on-board power supply, which is powered by the meter. This supply can drive 20 mA current into loads up to 600 ohms, for 12 V compliance. Isolation to signal ground and power ground eliminates problems caused by ground loops.

The addition of the analog output option turns Micro temperature meters into superb, isolated, linearized, 4-20 mA temperature transmitters with exceptional accuracy and high-speed response.

Specifications

Electrical
Power Source
Signal Source
Output Linearization
Output Levels
Compliance, 0-20 mA
Compliance, 0-10 V
Isolation
Accuracy
Output Nonlinearity
Output Resolution
Output Update Rate
Response Time
 

Provided by meter
Filtered or unfiltered digitized signal
Linearized to display
( 0-20 mA or 4-20 mA ) and 0-10 Vdc
12 V ( 0-600 ohm load )
2 mA ( 5 kOhm min load
Safety-rated to 250 Vac, 4.2 kVp per High Voltage Test
99.9% selected output, 98% non-selected output
<0.05%
12-bit ( .025% of FS )
56/s at 60 Hz power, 47/s at 50 Hz power
17 ms (unfiltered DPM)
Gate time + 30 ms + 0-2 periods (counter)

Scaling
Zero Output
Full Scale Output
Minimum Span

-99,999 to +99,999 (DPM), -999,999 to +999,999 (counter)
-99,999 to +99,999 (DPM), -999,999 to +999,999 (counter)
150 counts

J4 Pin Assignments

conanlog.gif (699 bytes)

Application Examples
  

Driving a Strip-chart Recorder

Driving a recorder using the analog output from a digital panel meter or electronic counter The 0-10 V output capability of the analog output board is ideal to drive a strip chart recorder. As for 4-20 mA, the 0-10 V output can be scaled to the meter reading to highlight signal level changes in a range of interest.

Use as an Isolated, Linearized 4-20 mA Transmitter

Using a digital panel meter or electronic counter as an isolated 4-20 mA current loop transmitter

0-20 mA output capability turns Micro meters and counters into high-accuracy, high-speed, isolated 4-20 mA transmitters. The output is linearized to the reading, a major benefit with thermocouple and RTD inputs. The 4-20 mA signal can be transmitted via twisted pair wires to a control room for supervisory process monitoring and control. Process meters in series with the signal can provide local readouts in engineering units where required.

Micro & Mighty Series Downloads

Electro-Numerics Inc. Logo

Digital Panel Meters
by Series

 Micro Meter/Controllers
 DIN Digital Indicators
 Summit Low Cost Meters
 Older Digital Panel Meters
 Catalogs & Price Lists
 Meter Owners Manuals
 Micro Downloads
 Meters Inquiry & RFQ

  

Large Digit Industrial Displays

 Mighty Series (to 5" LED)
 PI Series (2¼" LED)
 Flip-Digit Series (to 9")

 Catalogs & Price Lists
 Large Digit Inquiry & RFQ

  

Custom Magnetic Components

 Custom Transformers
 Coils, Inductors, Toroids
 Magnetic Sensors
 Magnetics Inquiry & RFQ
  

Sports Timing
Race Clocks
(to 9")

 LM Series, Flip-Digit
 XL Series, LED, Domestic
 XLC Series, LED, Int'l
 Mile-Marker 6" Raceclock

 Printing Race Timers
 Serial Remote Displays
 Raceclock Accessories
 Raceclock Dimensions
 Catalogs & Price Lists
 Sports Timer Inquiry

  

Information about Electro-Numerics

 Electro-Numerics Home
 About Electro-Numerics
 Electro-Numerics News
 General Inquiry

 Sitemap

 

 

© Electro-Numerics, Inc., 42213 Sarah Way, Temecula, CA 92590, USA
Tel: 800-854-8530 (USA), 951-699-2437;  Fax: 951-695-7246;  sales@electronumerics.com